Hello all,
I have a WDH1NC10000 white light 1To and 1 External Hard drive WD caviar 2To and i want to swap the two Hard drive.
Do you know if it's possible to make this ?
I don't find the method.
I search on the web since 2 days and only this website speak seriously about this Western Digital NAS.
PS: Sorry for my bad english :/
System will not mount partitions, path not found, can't http// getting…. "Warning: is_dir(): Stat failed for /DataVolume/_torrent_ (errno=5 - Input/output error) in /proto/SxM_webui/ctcs/ctcsconfig.inc on line 24" All threads say to FTP and that works, but in my case it does not.
Any suggestions?
Thanks in advance,
Mike
Hi
I'd like to use Tor.
I've install it via ipkg tor install
Configured it using http://astuces-webmaster.ch/page/tor-relay-synology
Launched it with /opt/bin/tor -f /opt/etc/tor/torrc —runasdaemon 1
After a launch, I got in the logs : "[err] Error from libevent: evmap.c:401: Assertion ctx failed in evmap_io_active" and a tor crash
Has anybody a idea on how to fix that ?
Thanks
D.
Hello,
My WD HD died recently after 3 full years and I decided to replace the drive with a WD RED Series Drive 1TB (WD10EFRX).
This drive sounds promising (has some NAS specific features, notably bigger load/unload cycles and big MeanTimeBetweenFailures).
BUT
1) it is SATA 3, claiming SATA 2 combatible
2) it is advanced formated (4KB physical sectors vs the classic 512). For this subject there should be no problem as it has 512 Logical addressing.
In fact I followed the great tutorial for White light debricking (How to fix bricked WD My Book World Edition White Light or install brand new disk? | iknowsomething.com) and booted the 01.02.14 firmware.
I started using the drive and files seemed to be copied.
BUT I noticed repeated ata errors at dmesg and smartctl. See below.
My question is, could theese errors be related to an SATA interface mismatch ?
dmesg init:
ox810sata: OX810 sata core. scsi0 : oxnassata ata1: SATA max UDMA/133 irq 18 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-9: WDC WD10EFRX-68PJCN0, 01.01A01, max UDMA/133 ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access WDC WDC WD10EFRX-68P 01.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk ox810sata: OX810 sata core. scsi1 : oxnassata ata2: SATA max UDMA/133 irq 18 ata2: SATA link down (SStatus 0 SControl 300) dmesg errors:
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 ata1.00: cmd ca/00:02:c8:c9:62/00:00:00:00:00/e0 tag 0 dma 1024 out res 51/10:02:c8:c9:62/00:00:00:00:00/e0 Emask 0x81 (invalid argument) ata1.00: status: { DRDY ERR } ata1.00: error: { IDNF } ata1.00: configured for UDMA/133 sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08 sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor] Descriptor sense data with sense descriptors (in hex): 72 0b 14 00 00 00 00 0c 00 0a 80 00 00 00 00 00 00 62 c9 c8 sd 0:0:0:0: [sda] ASC=0x14 ASCQ=0x0 end_request: I/O error, dev sda, sector 6474184 ata1: EH complete md: super_written gets error=-5, uptodate=0 sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 ata1.00: cmd ca/00:02:c8:c9:62/00:00:00:00:00/e0 tag 0 dma 1024 out res 51/10:02:c8:c9:62/00:00:00:00:00/e0 Emask 0x81 (invalid argument) ata1.00: status: { DRDY ERR } ata1.00: error: { IDNF } ata1.00: configured for UDMA/133 sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08 sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor] Descriptor sense data with sense descriptors (in hex): 72 0b 14 00 00 00 00 0c 00 0a 80 00 00 00 00 00 00 62 c9 c8 sd 0:0:0:0: [sda] ASC=0x14 ASCQ=0x0 end_request: I/O error, dev sda, sector 6474184 ata1: EH complete md: super_written gets error=-5, uptodate=0 sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA smartctl output:
=== START OF INFORMATION SECTION === Device Model: WDC WD10EFRX-68PJCN0 Serial Number: WD-WCC4J1263311 Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 9 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Jan 5 17:40:27 2014 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (15840) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 179) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 137 134 021 Pre-fail Always - 4125 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 14 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 28 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 8 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 0 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 243 194 Temperature_Celsius 0x0022 109 105 000 Old_age Always - 34 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 7 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7 occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 02 c8 c9 62 e0 Error: IDNF at LBA = 0x0062c9c8 = 6474184 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 02 c8 c9 62 e0 00 21:32:55.040 WRITE DMA ca 00 02 c8 c9 62 e0 00 21:32:21.748 WRITE DMA Error 6 occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 02 c8 c9 62 e0 Error: IDNF at LBA = 0x0062c9c8 = 6474184 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 02 c8 c9 62 e0 00 21:32:10.878 WRITE DMA ca 00 02 c8 c9 62 e0 00 21:31:45.820 WRITE DMA Error 5 occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 08 c0 ca 3c e0 Error: IDNF at LBA = 0x003ccac0 = 3984064 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 08 c0 ca 3c e0 00 20:50:04.045 WRITE DMA ca 00 08 c0 ca 3c e0 00 20:49:52.994 WRITE DMA Error 4 occurred at disk power-on lifetime: 13 hours (0 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 02 c8 c9 62 e0 Error: IDNF at LBA = 0x0062c9c8 = 6474184 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 02 c8 c9 62 e0 00 06:33:11.264 WRITE DMA c8 00 08 50 bb 0c e0 00 06:33:01.814 READ DMA ca 00 02 c8 c9 62 e0 00 06:32:46.965 WRITE DMA Error 3 occurred at disk power-on lifetime: 13 hours (0 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 50 bb 0c e0 Error: UNC 8 sectors at LBA = 0x000cbb50 = 834384 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 50 bb 0c e0 00 06:09:10.569 READ DMA ca 00 02 c8 c9 62 e0 00 06:08:58.687 WRITE DMA ca 00 01 d0 ca 62 e0 00 06:08:58.482 WRITE DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Also another thing that might be of interest is that from the NAS the physical sector size is reported 512B while plugged on a PC it as reported 4096B (but logical size still 512B)
Output of parted /dev/sda; p p; (from the NAS)
Model: WDC WDC WD10EFRX-68P (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 32.9MB 2040MB 2007MB ext3 primary raid 2 2040MB 2303MB 263MB linux-swap primary raid 3 2303MB 3315MB 1012MB ext3 primary raid 4 3315MB 1000GB 997GB primary raid Is there any way to create password protected folders on WD book live (WDBL)?
I have 4 different user account created on WDBL, having different privileges are working great until you have installed iMediaShare on your iPad or iPhone. Through this application or other applications like this, you can access all of the user profiles and all of the folders/files they’ve created. No privacy what so ever. This is bad!!!
Hello,
I have a MBWE with 1 TB and I've change it with a hard drive of 250 GB. To put it I used the guide with title "how-to-fix-bricked-wd-my-book-world-edition-or-install-brand-new-disk"
I configured the file mbwe-config.sh and I ran the following command:
$ sudo bash ./mbwe-install.sh
I connected the hard drive and I go to the web management. A % is showed and it took many hours until finally finished booting. I checked all and I saw that the DataVolume had an error. I entered through ssh and tried to mount it at /DataVolume but it also gave errors. How I hadn't data, I formatted it and I could mount:
$ mkfs.xfs /dev/md2
$ mount /dev/md2 /DataVolume
But when I look at the partitions are mounted, I don't see md1:
$ df -h
Filesystem Size Used Available Use% Mounted on
/dev/md0 1.8G 115.2M 1.6G 6% /
/dev/md3 949.6M 120.4M 780.9M 13% /var
/dev/md2 229.7G 8.8M 229.7G 0% /DataVolume
/dev/ram0 61.9M 16.0k 61.9M 0% /mnt/ram
Is this okay? Do I have to mount md1? Where?
PD: Sorry for my english
Regards
Hello
I have a MBWE.
I had a problem with my device then I bought a WD network board to replace.
But now I have a WD HDD formatted (NTFS format) and the new network board.
is possible to convert this HDD to configure correctly the system?
Does a iso exist to load inmy HD?
TH
I delete all partitions on two brand new green drives.
I setup a new drive A. Put it in, it works fine.
I put in drive B, format. Wait.
Change to Raid I.
Everything works fine.
SSL, the whole thing is great.
I turn it off, turn it back on. It's fine.
I turn off, turn it back on. Drive A failed.
I swap A with B. Drive B failed.
Format Drive B from within since it's detected as a new internal drive.
Files sync. Everything is fine again.
Turn it off, back on. It's fine.
Turn it off, back on. Drive A failed (which was the original drive B).
Swap it out. I can format it.
Any ideas what the hell is going on?
I've started fresh twice already.
And these are brand new drives that work fine when I mount them externally. My old drives also reported no errors when I did a complete 8hr disk scan. But I bought these just in case.
Any help is greatly appreciated!!
I've hack my Live Duo 3Tb and begin to upgrade it from debian site. Then I reboot NAS and it didn't loaded. I plug to UART and see at console next:
----- Checking Boot Partitions ----- U-Boot 2009.08-svn54115 (Nov 15 2011 - 10:54:56), Build: 0.0.12 CPU: AMCC PowerPC APM82181 Rev. D at 800 MHz (PLB=200, OPB=100, EBC=100 MHz) Security support Bootstrap Option E - Boot ROM Location NOR/SRAM (8 bits) 32 kB I-Cache 32 kB D-Cache Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB U-Boot 2009.08-svn54115 (Nov 15 2011 - 10:54:56), Build: 0.0.12 CPU: AMCC PowerPC APM82181 Rev. D at 800 MHz (PLB=200, OPB=100, EBC=100 MHz) Security support Bootstrap Option E - Boot ROM Location NOR/SRAM (8 bits) 32 kB I-Cache 32 kB D-Cache Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB I2C: ready DRAM: Auto calibration 256 MB FLASH: 512 kB DTT: 1 FAILED INIT Net: PHY EC1 Register: 0x2c8c ppc_4xx_eth0 Type run flash_nfs to mount root filesystem over NFS p=============================================================================q |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::WWWWWWWWW::::WWWWWWW::::::::WWWWWWW::DDDDDDDDDDDDDDDDD::::::::::::| |:::::::::::WWWWWWWW::::WWWWWWWW:::::::WWWWWWW::DDDDDDDDDDDDDDDDDDDD::::::::::| |:::::::::::WWWWWWWW:::WWWWWWWWW::::::WWWWWWW::DDDDDDDDDDDDDDDDDDDDDD:::::::::| |::::::::::::::::::::::::::::::::::::::::::::::::::::::::::DDDDDDDDDDD::::::::| |:::::::::::WWWWWWW:::WWWWWWWWWW::::WWWWWWW::DDDDDDDDD:::::::DDDDDDDDD::::::::| |:::::::::::WWWWWWW::WWWWWWWWWWW:::WWWWWWW::DDDDDDDDD::::::::DDDDDDDDD::::::::| |:::::::::::WWWWWW::WWWWWW::WWWWW:WWWWWWW::DDDDDDDDDD:::::::DDDDDDDDDD::::::::| |:::::::::::WWWWWWWWWWWWW:::WWWWWWWWWWWW::DDDDDDDDDD::::::DDDDDDDDDDD:::::::::| |:::::::::::WWWWWWWWWWWW::::WWWWWWWWWWW::DDDDDDDDDDD:::DDDDDDDDDDDDD::::::::::| |:::::::::::WWWWWWWWWWW:::::WWWWWWWWWW::DDDDDDDDDDDDDDDDDDDDDDDDDD::::::::::::| |:::::::::::WWWWWWWWWW::::::WWWWWWWWW::DDDDDDDDDDDDDDDDDDDDDDDDD::::::::::::::| |:::::::::::WWWWWWWWW:::::::WWWWWWWW::DDDDDDDDDDDDDDDDDDDDDDDD::::::::::::::::| |:::::::::::WWWWWWWW::::::::WWWWWWW::DDDDDDDDDDDDDDDDDDDD:::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| b=============================================================================d Hit any key to stop autoboot: 0 USB: OTG-Controller ID(0x4F54) Version(0x290A) Err detect usb time out hostport.d32 0x00001000 0 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported Board is not configured for test. Do normal boot. ----- Checking Boot Partitions ----- SATA DWC initialization 0 init: Waiting for device... sata_dwc: Device found scan: Waiting for device... SATA DWC initialization 1 init: Waiting for device... sata_dwc: Device found scan: Waiting for device... Loading file "/boot/boot.scr" from sata device 1:1 (gpt1) 1223 bytes read 1:1 ## Executing script at 00100000 Boot from md0 U-boot configuration =============== Loading Linux kernel ================= =============== Device tree ================= =============== Root filesystem ================= SATA DWC initialization 0 init: Waiting for device... sata_dwc: Device found scan: Waiting for device... SATA DWC initialization 1 init: Waiting for device... sata_dwc: Device found scan: Waiting for device... Loading file "/boot/uImage" from sata device 1:1 (gpt1) 3501769 bytes read Loading file "/boot/apollo3g.dtb" from sata device 1:1 (gpt1) 8373 bytes read Loaded part 1 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux-2.6.32.11-svn70860 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 3501705 Bytes = 3.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01800000 Booting using the fdt blob at 0x1800000 Uncompressing Kernel Image ... OK Loading Device Tree to 00ffa000, end 00fff0b4 ... OK Using PowerPC 44x Platform machine description Linux version 2.6.32.11-svn70860 (steveh@steveh-pc) (gcc version 4.2.2) #1 Thu May 17 13:32:51 PDT 2012 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00001000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00001000 MMU: Allocated 1088 bytes of context maps for 255 contexts Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4094 Kernel command line: root=/dev/md1 rw rootfstype=ext3 rootflags=data=ordered console=ttyS0,115200 PID hash table entries: 1024 (order: -4, 4096 bytes) Dentry cache hash table entries: 32768 (order: 1, 131072 bytes) Inode-cache hash table entries: 16384 (order: 0, 65536 bytes) Memory: 253184k/262144k available (7168k kernel code, 8960k reserved, 512k data, 749k bss, 448k init) Kernel virtual memory layout: * 0xfffe0000..0xffff0000 : fixmap * 0xfd600000..0xfe000000 : consistent mem * 0xfd600000..0xfd600000 : early ioremap * 0xd1000000..0xfd600000 : vmalloc & ioremap Hierarchical RCU implementation. NR_IRQS:512 UIC0 (32 IRQ sources) at DCR 0xc0 UIC1 (32 IRQ sources) at DCR 0xd0 UIC2 (32 IRQ sources) at DCR 0xe0 UIC3 (32 IRQ sources) at DCR 0xf0 clocksource: timebase mult[500000] shift[22] registered Security Framework initialized Mount-cache hash table entries: 8192 xor: measuring software checksum speed 8regs : 128.000 MB/sec 8regs_prefetch: 240.000 MB/sec 32regs : 112.000 MB/sec 32regs_prefetch: 240.000 MB/sec xor: using function: 32regs_prefetch (240.000 MB/sec) NET: Registered protocol family 16 OCM1: 32768 Bytes (enabled) OCM1: 32768 Bytes (non-cached) OCM1: 0 Bytes (cached) 256k L2-cache enabled PCI: Probing PCI hardware bio: create slab <bio-0> at 0 SCSI subsystem initialized raid6: int32x1 185 MB/s raid6: int32x2 189 MB/s raid6: int32x4 197 MB/s raid6: int32x8 189 MB/s raid6: using algorithm int32x4 (197 MB/s) mod_init:1052 ppc460ex_dma_per_chan_init:1064 Switching to clocksource timebase init_pipe_fs: pipe_inode_cache initialized NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 0, 65536 bytes) TCP established hash table entries: 8192 (order: 0, 65536 bytes) TCP bind hash table entries: 8192 (order: -1, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Probing AMCC DMA driver PPC4xx PLB DMA engine IRQ 20 __ioremap(): phys addr 0x0 is RAM lr c04d50c4 PPC460ex PLB DMA engine @0x00_00000100 size 263 new_chan->chan_id 0x0 new_chan->chan->chan_id 0x0 apollo3g_gpio_init: GPIO 1 @ 0xe0000000; GPIO 2 @ 0xe1000000 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Slow work thread pool: Starting up Slow work thread pool: Ready NTFS driver 2.1.29 [Flags: R/O]. JFFS2 version 2.2. (NAND) ?© 2001-2006 Red Hat, Inc. fuse init (API version 7.13) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 492 Cryptodev Interface Loaded User space CryptoAPI driver v0.1 loaded async_tx: api initialized (async) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 19) is a 16550A console [ttyS0] enabled 4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 19) is a 16550 brd: module loaded sata-dwc 4bffd1000.sata: Gettting DMA channel 0 sata-dwc 4bffd1000.sata: id 0, controller version 1.91 sata-dwc 4bffd1000.sata: DMA initialized sata-dwc 4bffd1000.sata: DMA CFG = 0x00000001 dma_register_interrupt register irq (25) ata4294967295: sata_dwc_port_start: setting burst size in DBTSR: 0x00100010 sata-dwc 4bffd1000.sata: **** GEN II speed rate negotiated scsi0 : sata-dwc ata1: SATA max UDMA/133 irq 23 sata-dwc 4bffd1800.sata: Gettting DMA channel 1 sata-dwc 4bffd1800.sata: id 0, controller version 1.91 sata-dwc 4bffd1800.sata: DMA initialized sata-dwc 4bffd1800.sata: DMA CFG = 0x00000001 dma_register_interrupt register irq (25) ata4294967295: sata_dwc_port_start: setting burst size in DBTSR: 0x00100010 sata-dwc 4bffd1800.sata: **** GEN II speed rate negotiated scsi1 : sata-dwc ata2: SATA max UDMA/133 irq 27 Found: SST 39LF040 4fff80000.nor_flash: Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Creating 2 MTD partitions on "4fff80000.nor_flash": 0x000000000000-0x000000020000 : "3genv" 0x000000020000-0x000000080000 : "u-boot" ndfc 4fff80000.ndfc: failed to get memory ndfc: probe of 4fff80000.ndfc failed with error -5 e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 e1000e: Copyright (c) 1999-2008 Intel Corporation. PPC 4xx OCP EMAC driver, version 3.54 mal0: descriptor-memory = ocm MAL: Enabled Interrupt Coal TxCnt: 1 RxCnt: 8 TxTimer: 0 RxTimer: 10000 MAL v2 /plb/mcmal, 1 TX channels, 1 RX channels RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support TAH /plb/opb/emac-tah@ef601350 initialized /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode bcm54610_init: before 0x2c8c, after 0x2c8c bcm54610_init: before 0x01e1, 0x0200; after 0x0141, 0x0200 eth0: EMAC-0 /plb/opb/ethernet@ef600c00, MAC 00:90:a9:bb:3e:02 eth0: found BCM54610 Gigabit Ethernet PHY (0x01) Intel(R) Gigabit Ethernet Network Driver - version 1.3.16-k2 Copyright (c) 2007-2009 Intel Corporation. tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> Fusion MPT base driver 3.04.12 Copyright (c) 1999-2008 LSI Corporation Fusion MPT SAS Host driver 3.04.12 input: rst_button as /devices/virtual/input/input0 i2c /dev entries driver ibm-iic 4ef600700.i2c: using standard (100 kHz) mode md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 Registered led device: a3g_led AMCC 4xx PKA v0.1 @0x04_00114000 size 16384 IRQ 39 Initializing PKA... PKA Driver Successfully Initialized Reading pvr value = 12c41c82 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F0300) ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F0300) Interrupt status = 0x00042020 dev status = 0x03087722 Interrupt status = 0x00042020 dev status = 0x03087722 apm82181-adma: Probing AMCC APM82181 ADMA engines... AMCC(R) APM82181 ADMA Engine found [1]: ( capabilities: memcpy ) --------------- dma_async_device_register: 683------------------------- ata2.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133 ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 1/32) apm82181 adma1: allocated 512 descriptor slots AMCC(R) APM82181 ADMA Engine found [2]: ( capabilities: memcpy ) --------------- dma_async_device_register: 683------------------------- ata1.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133 ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 1/32) apm82181 adma2: allocated 512 descriptor slots AMCC(R) APM82181 ADMA Engine found [3]: ( capabilities: memcpy ) --------------- dma_async_device_register: 683------------------------- apm82181 adma3: allocated 512 descriptor slots ata1.00: configured for UDMA/133 ata2.00: configured for UDMA/133 blk_queue_max_hw_segments: set to minimum 1 oprofile: using timer interrupt. Macsec proc interface Initiliazed Registered Macsec Interface IPv4 over IPv4 tunneling driver scsi 0:0:0:0: Direct-Access ATA WDC WD30EZRX-00M 80.0 PQ: 0 ANSI: 5 GRE over IPv4 tunneling driver sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: Attached scsi generic sg0 type 0 blk_queue_max_hw_segments: set to minimum 1 ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver scsi 1:0:0:0: Direct-Access ATA WDC WD30EZRX-00M 80.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 1:0:0:0: [sdb] 4096-byte physical blocks sd 1:0:0:0: Attached scsi generic sg1 type 0 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> sda: sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb:drivers/rtc/hctosys.c: unable to open rtc device (rtc0) sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sdb1 sdb2 sdb3 sdb4 sd 1:0:0:0: [sdb] Attached SCSI disk md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: invalid raid superblock magic on sda3 md: sda3 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sda4 md: sda4 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sdb3 md: sdb3 does not have a valid v0.90 superblock, not importing! md: invalid raid superblock magic on sdb4 md: sdb4 does not have a valid v0.90 superblock, not importing! md: Scanned 8 and added 4 devices. md: autorun ... md: considering sdb2 ... md: adding sdb2 ... md: adding sdb1 ... md: adding sda2 ... md: adding sda1 ... md: created md1 md: bind<sda1> md: bind<sda2> md: bind<sdb1> md: bind<sdb2> md: running: <sdb2><sdb1><sda2><sda1> md: kicking non-fresh sda2 from array! md: unbind<sda2> md: export_rdev(sda2) md: kicking non-fresh sda1 from array! md: unbind<sda1> md: export_rdev(sda1) md1: WARNING: sdb2 appears to be on the same physical disk as sdb1. True protection against single-disk failure might be compromised. raid1: raid set md1 active with 2 out of 4 mirrors md1: detected capacity change from 0 to 2047803392 md: ... autorun DONE. md1: unknown partition table kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on md1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) on device 9:1. Freeing unused kernel memory: 448k init INIT: version 2.86 booting Retrieving saved clock:Tue Feb 19 21:40:40 MSK 2013 Set clock to Tue Feb 19 21:40:40 MSK 2013 . /etc/rcS.d/S02restoreSettings.sh: Checking settings: test/restore....._: pkg: wd-nas [wd-nas.preinst] 02/19/13 18:40:41: test [wd-nas.preinst] 02/19/13 18:40:41: done. [wd-nas.postinst] 02/19/13 18:40:42: test context=test [wd-nas.postinst] 02/19/13 18:40:42: done. _: pkg: networking-general [networking-general.preinst] 02/19/13 18:40:43: test [networking-general.preinst] 02/19/13 18:40:43: done. [networking-general.postinst] 02/19/13 18:40:43: test context=test [networking-general.postinst] 02/19/13 18:40:43: done. _: pkg: apache-php-webdav [apache-php-webdav.preinst] 02/19/13 18:40:44: test [apache-php-webdav.preinst] 02/19/13 18:40:44: done. [apache-php-webdav.postinst] 02/19/13 18:40:44: test context=test [apache-php-webdav.postinst] 02/19/13 18:40:44: done. _: pkg: date-time [date-time.preinst] 02/19/13 18:40:45: test [date-time.preinst] 02/19/13 18:40:45: done. [date-time.postinst] 02/19/13 18:40:45: test context=test [date-time.postinst] 02/19/13 18:40:45: done. _: pkg: alerts [alerts.preinst] 02/19/13 18:40:46: test [alerts.preinst] 02/19/13 18:40:46: done. [alerts.postinst] 02/19/13 18:40:46: test context=test [alerts.postinst] 02/19/13 18:40:46: done. _: pkg: admin-rest-api [admin-rest-api.preinst] 02/19/13 18:40:47: test [admin-rest-api.preinst] 02/19/13 18:40:47: test() [admin-rest-api.preinst] 02/19/13 18:40:47: done. [admin-rest-api.postinst] 02/19/13 18:40:48: test context=test drwxrwsr-x 2 root www-data 4096 May 16 2012 config [admin-rest-api.postinst] 02/19/13 18:40:48: permissions check for //var/www/Admin/webapp/config: PASSED [admin-rest-api.postinst] 02/19/13 18:40:48: permissions check for /dynamicconfig.ini: FAILED drwxrwxr-x 2 root www-data 4096 Feb 17 15:34 orion [admin-rest-api.postinst] 02/19/13 18:40:48: permissions check for //usr/local/nas/orion/: PASSED -rwxrwxr-x 1 root www-data 79872 Feb 17 15:34 //usr/local/nas/orion//orion.db [admin-rest-api.postinst] 02/19/13 18:40:48: permissions check for //usr/local/nas/orion//orion.db: PASSED [admin-rest-api.postinst] 02/19/13 18:40:48: setup test for admin-rest-api: PASSED [admin-rest-api.postinst] 02/19/13 18:40:48: done. _: pkg: drive-lib [drive-lib.preinst] 02/19/13 18:40:48: test [drive-lib.preinst] 02/19/13 18:40:48: done. [drive-lib.postinst] 02/19/13 18:40:49: test context=test [drive-lib.postinst] 02/19/13 18:40:49: done. _: pkg: data-volume-config [data-volume-config.preinst] 02/19/13 18:40:49: test [data-volume-config.preinst] 02/19/13 18:40:49: done. [data-volume-config.postinst] 02/19/13 18:40:50: test context=test [data-volume-config.postinst] 02/19/13 18:40:50: done. _: pkg: upnp-nas [upnp-nas.preinst] 02/19/13 18:40:50: test [upnp-nas.preinst] 02/19/13 18:40:50: done. [upnp-nas.postinst] 02/19/13 18:40:51: test context=test [upnp-nas.postinst] 02/19/13 18:40:51: done. _: pkg: dlna-server-access [dlna-server-access.preinst] 02/19/13 18:40:51: test [dlna-server-access.preinst] 02/19/13 18:40:51: done. [dlna-server-access.postinst] 02/19/13 18:40:52: test context=test [dlna-server-access.postinst] 02/19/13 18:40:52: done. _: pkg: itunes [itunes.preinst] 02/19/13 18:40:52: test [itunes.preinst] 02/19/13 18:40:52: done. [itunes.postinst] 02/19/13 18:40:53: test context=test _: pkg: nas-safepoint [nas-safepoint.preinst] 02/19/13 18:40:53: test [nas-safepoint.preinst] 02/19/13 18:40:53: done. [nas-safepoint.postinst] 02/19/13 18:40:54: test context=test [nas-safepoint.postinst] 02/19/13 18:40:54: done. _: pkg: webui [webui.preinst] 02/19/13 18:40:54: test [webui.preinst] 02/19/13 18:40:54: done. [webui.postinst] 02/19/13 18:40:55: test context=test [webui.postinst] 02/19/13 18:40:55: done. _: pkg: orion-resources [orion-resources.preinst] 02/19/13 18:40:55: test [orion-resources.preinst] 02/19/13 18:40:55: done. [orion-resources.postinst] 02/19/13 18:40:55: test context=test [orion-resources.postinst] 02/19/13 18:40:56: done. _: pkg: afp [afp.preinst] 02/19/13 18:40:56: test [afp.preinst] 02/19/13 18:40:56: done. [afp.postinst] 02/19/13 18:40:56: test context=test [afp.postinst] 02/19/13 18:40:56: done. done. Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...done. Setting parameters of disc: (none). [: 41Disable EMAC EMI Fix : 28.130: unexpected operator EMI patch disabled... cpu=APM82181 rev=28.130 Activating swap...done. Cleaning up ifupdown.... Loading kernel modules...done. Checking file systems...fsck from util-linux-ng 2.17.2 done. Setting kernel variables (/etc/sysctl.conf)...done. Setting kernel variables (/etc/sysctl.d/dlna.conf)...done. Setting kernel variables (/etc/sysctl.d/inotify.conf)...done. Setting kernel variables (/etc/sysctl.d/mtu.conf)...done. Mounting local filesystems...done. Activating swapfile swap...done. Setting up networking.... [: 72: unexpected operator [: 72: unexpected operator Configuring network interfaces...[: 10: enabled: unexpected operator logger: hostname=LinsiteNAS [: 58: false: unexpected operator [: 5: 4: unexpected operator [: 5: 4: unexpected operator [: 6: 4: unexpected operator Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit eth0: link is up, 1000 FDX, pause enabled Listening on LPF/eth0/00:90:a9:bb:3e:02 Sending on LPF/eth0/00:90:a9:bb:3e:02 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 DHCPOFFER from 10.0.0.1 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 10.0.0.1 /etc/init.d/samba: 13: source: not found Reloading /etc/samba/smb.conf: smbd onlyNo process in pidfile '/var/run/samba/smbd.pid' found running; none killed. . bound to 10.0.0.4 -- renewal in 42208 seconds. [: 10: enabled: unexpected operator Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon. logger: hostname=LinsiteNAS [: 58: false: unexpected operator [: 5: 4: unexpected operator [: 5: 4: unexpected operator /etc/init.d/samba: 13: source: not found [: 6: 0: unexpected operator done. Starting portmap daemon.... INIT: Entering runlevel: 1 /usr/local/sbin/drive_helper.sh: 43: Syntax error: "(" unexpected (expecting "}") /etc/rc1.d/S02purgelogs.sh: 14: Syntax error: "(" unexpected (expecting "}") Starting ramlog-tmpfs 2.0.0: . Starting enhanced syslogd: rsyslogd. /etc/rc1.d/S04apache2: 13: source: not found /usr/local/sbin/drive_helper.sh: 43: Syntax error: "(" unexpected (expecting "}") /usr/local/sbin/drive_helper.sh: 43: Syntax error: "(" unexpected (expecting "}") S15mountDataVolume.sh: begin script: start >>>> mount data volume...[: 159: unexpected operator [: 159: unexpected operator [: 159: unexpected operator mount: special device /dev/md3 does not exist logger: mount of /dev/md3 on /DataVolume failed: 32 umount2: Invalid argument umount: /DataVolume: not mounted fsck from util-linux-ng 2.17.2 fsck.ext2: No such file or directory while trying to open /dev/md3 /dev/md3: The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> logger: fsck of /dev/md3 on failed: 8 [: 159: 1: unexpected operator [: 159: 0: unexpected operator mount: special device /DataVolume/cache does not exist mount: special device /DataVolume/shares does not exist mount: special device /DataVolume/shares does not exist [: 159: unexpected operator _: pkg: wd-nas _: pkg: networking-general _: pkg: apache-php-webdav _: pkg: date-time _: pkg: alerts _: pkg: admin-rest-api [admin-rest-api.preinst] 02/19/13 18:41:23: test [admin-rest-api.preinst] 02/19/13 18:41:23: test() [admin-rest-api.preinst] 02/19/13 18:41:23: done. [admin-rest-api.postinst] 02/19/13 18:41:23: test context=test drwxrwsr-x 2 root www-data 4096 May 16 2012 config [admin-rest-api.postinst] 02/19/13 18:41:23: permissions check for //var/www/Admin/webapp/config: PASSED [admin-rest-api.postinst] 02/19/13 18:41:23: permissions check for /dynamicconfig.ini: FAILED drwxrwxr-x 2 root www-data 4096 Feb 17 15:34 orion [admin-rest-api.postinst] 02/19/13 18:41:23: permissions check for //usr/local/nas/orion/: PASSED -rwxrwxr-x 1 root www-data 79872 Feb 17 15:34 //usr/local/nas/orion//orion.db [admin-rest-api.postinst] 02/19/13 18:41:23: permissions check for //usr/local/nas/orion//orion.db: PASSED [admin-rest-api.postinst] 02/19/13 18:41:23: setup test for admin-rest-api: PASSED [admin-rest-api.postinst] 02/19/13 18:41:23: done. _: pkg: drive-lib _: pkg: data-volume-config _: pkg: upnp-nas _: pkg: dlna-server-access _: pkg: itunes _: pkg: nas-safepoint _: pkg: webui _: pkg: orion-resources _: pkg: afp swapon: cannot stat /dev/md2: No such file or directory Kernel API version: 2 settrustees API version: 2 Pass 1: Checking for parse errors Could not find device /dev/md3 Parse error /tmp/trustees.mod:9 done. Starting Network Interface Plugging Daemon: eth0. Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmontools (warning). Starting reset button monitor: resetbtnd. S99wdInitFinalize: begin script: start /etc/rc1.d/S99wdInitFinalize: 26: source: not found /usr/local/sbin/ledConfig.sh: 32: Syntax error: "(" unexpected INIT: no more processes left in this runlevel Can somebody help me to restore original FW on NAS over TFTP or USB-stick?
Also - I haven't SATA port on my Mac.
I think that after update from debian site - i rewrite bash 3.0 to bash 4.0. And some script's finish to work. At U-BOOT function's I didn't find any command to rewrite single file on internal NAS disk. NEED HELP!!
Hello everyone,
im new owner of the My Book live 2TB version. I allready installed pyload but in the root, so the problem is there is only few MB left free space and i want to change the download folder into the live book Download folder i created. Can someone help me with that?
When i type in putty this /root/.pyload i can not get config file.
Please tell me how do i change the dowload folder?
Hi guys
i know you can install the OpenVPN server on a my book world (white light). But is there any way to connect the book to a VPN Provider like hidemyass.com via terminal? So all the download traffic goes through this tunnel.
Thanks :-)
Hy Guys seems impossible to install ash on the my book world ed II. Any ideas? Mirrors?
Hi guys,
Firstly, I like to thank you all for such great help on your tutorials, I have been playing with my old white light for 3 days now just for the fun of it.
Talking about fun, I have been playing around with media solutions and came across Plex which I found really cool on the Samsung TV, the only problem is that I am running it on PC and pointing to the files on the MyBook. I came across the Tut for installing Debian and Plex but made a disaster of it, so much that I had to rip the disk out and reload the partitions by hooking it directly to the PC (enough of a challenge for my skills). Anyway, I'm not too keen on the Twonky v5 and not sure how much of an improvement v6 or v7 will be so I want to take the road down Plex way if it is possible without having to install a new OS. I wouldn't mind so much to install Debian just as long as I can maintain the ability to keep the NAS working as a time machine for my mac at the same time.
Any clues on how to do this?
Just found my never-used 2x500Gb Blue Rings MBWE in the Old Hardware Closet. It's been SSH hacked, but that was all I did to it at the time. It's FW version 02.00.18 currently.
Now that hard drive technology is so inexpensive, is it possible for me to install the basic operating system onto a pair of 3 or 4Tb disks? I suspect that there may be hardware issues, but I thought I'd ask first before I spent the cash on the disks and discovered it was not going to work out.
So, oh wise wizards of Embedded Linux, please let this NetBSD junkie know his best options for upgrading the disks in this fun little box.
Thanks in advance!
I am trying to give my WD My Book world a second life as an rsync backup target. I am following the guides to install but I need to edit a file in /etc/default/rsync but I can't even find /etc/default, there is no default in /etc. I have enabled ssh, am logged in as root using filezilla and ssh protocol. Have just reinstalled it to default but can't see the folder. There is a /factorydefault folder but it doesn't have an rsync file as well.
Here is what I see (not allowed to post image link due to low post count)
DataVolume
dev
etc
—.factoryDefault
—hotplug
—hotplug.d
—init.d
—mionet
—netatalk
—network
—samba
—sysconfig
Extendvolume
Some Specifications of this new device. Architecture is armhf with dual core CPU
WDMyCloud:/tmp# cat /proc/cpuinfo Processor : ARMv7 Processor rev 1 (v7l) processor : 0 BogoMIPS : 1292.69 processor : 1 BogoMIPS : 1299.25 Features : swp half thumb fastmult vfp edsp neon vfpv3 tls CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x2 CPU part : 0xc09 CPU revision : 1 Hardware : Comcerto 2000 EVM Revision : 0001 Serial : 0000000000000000 WDMyCloud:/tmp# cat /proc/meminfo MemTotal: 230560 kB MemFree: 74416 kB Buffers: 6292 kB Cached: 82460 kB SwapCached: 8932 kB Active: 52664 kB Inactive: 77424 kB Active(anon): 22148 kB Inactive(anon): 47236 kB Active(file): 30516 kB Inactive(file): 30188 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 500732 kB SwapFree: 486424 kB Dirty: 420 kB Writeback: 0 kB AnonPages: 33520 kB Mapped: 11740 kB Shmem: 28048 kB Slab: 17980 kB SReclaimable: 11396 kB SUnreclaim: 6584 kB KernelStack: 1400 kB PageTables: 1824 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 616012 kB Committed_AS: 340704 kB VmallocTotal: 516096 kB VmallocUsed: 38308 kB VmallocChunk: 458748 kB Running Processes
ID Owner Started Command 1 root 16:03 init [2] 1848 root 16:04 udevd --daemon 2241 root 16:04 udevd --daemon 2242 root 16:04 udevd --daemon 3325 root 16:04 /sbin/rpcbind -w 3546 root 16:04 /usr/sbin/rsyslogd -c5 3736 root 16:04 /usr/sbin/apache2 -k start 20529 www-data 22:10 /usr/sbin/apache2 -k start 29106 www-data 23:22 /usr/sbin/apache2 -k start 29787 www-data 23:24 /usr/sbin/apache2 -k start 31580 www-data 23:32 /usr/sbin/apache2 -k start 5145 root 16:04 /usr/sbin/ifplugd -i eth0 -q -f -u0 -d5 -w -I 5183 root 16:04 /usr/local/bin/wd-btnd /dev/input/button system 4 /usr/local/sbin/resetButtonAct ... 5683 root 16:04 /sbin/mdadm --monitor --pid-file /var/run/mdadm/monitor.pid --daemonise --scan - ... 5781 root 16:04 /bin/sh /usr/local/sbin/monitorTemperature.sh 32160 root 23:34 sleep 1800 5871 root 16:04 /bin/bash /usr/local/sbin/monitorio.sh 32390 root 23:36 sleep 60 6009 root 16:04 /usr/sbin/rpc.mountd --manage-gids 6039 root 16:04 /usr/sbin/nmbd -D 6043 root 16:04 /usr/sbin/smbd -D 6060 root 16:04 /usr/sbin/smbd -D 6081 root 16:04 /usr/sbin/netatalk -F /etc/netatalk/afp.conf 6083 root 16:04 /usr/sbin/afpd -d -F /etc/netatalk/afp.conf 9951 root 16:31 /usr/sbin/cnid_metad -d -F /etc/netatalk/afp.conf 6520 root 16:05 /usr/local/wdmcserver/bin/wdmcserver -v:/tmp/Volumes.xml 6618 root 16:05 /usr/local/wdmcserver/bin/wdphotodbmerger 6645 root 16:05 /usr/sbin/cron 6693 root 16:05 /usr/local/bin/wddispatcher 6736 root 16:05 /usr/local/bin/wdnotifier 6803 root 16:05 /usr/local/bin/wdAutoMounter 7043 root 16:05 /sbin/getty -L ttyS0 115200 vt100 7981 root 16:22 /usr/local/orion/communicationmanager/communicationmanager -f 120 8050 root 16:22 openvpn /usr/local/orion/openvpnclient/client.ovpn 10649 root 16:34 /usr/local/bin/mDNSResponderPosix -b -f //etc/nas/mDNSResponder.conf -P /var/run ... 10889 root 16:35 /usr/sbin/vsftpd 11602 root 16:37 /usr/sbin/sshd 13410 root 16:39 sshd: root@pts/0 13457 root 16:40 -bash 12294 root 16:37 /usr/local/bin/forked-daapd 12368 root 16:37 /usr/local/bin/lld2d eth0 12453 root 16:37 /usr/local/twonkymedia-7/twonkystarter -D -ip 192.168.9.10 -httpport 9000 -appda ... 12455 root 16:37 /usr/local/twonkymedia-7/twonkyserver -D -ip 192.168.9.10 -httpport 9000 -appdat ... 12822 root 16:37 /usr/local/bin/upnp_nas_device -webdir /var/local/upnp_nas_device -desc nasdevic ... 31676 root 23:32 /usr/bin/perl /usr/share/webmin/miniserv.pl /etc/webmin/miniserv.conf 32525 root 23:36 /usr/share/webmin/proc/index_tree.cgi 32563 root 23:36 sh -c ps --cols 2048 -eo user:80,ruser:80,group:80,rgroup:80,pid,ppid,pgid,pcpu, ... 32564 root 23:36 ps --cols 2048 -eo user:80,ruser:80,group:80,rgroup:80,pid,ppid,pgid,pcpu,vsz,ni ... 32557 root 23:36 /usr/bin/perl /usr/share/webmin/miniserv.pl /etc/webmin/miniserv.conf 32559 root 23:36 /usr/bin/perl /usr/share/webmin/miniserv.pl /etc/webmin/miniserv.conf 2 root 16:03 [kthreadd] 3 root 16:03 [cpu1_hotplug_th] 4 root 16:03 [ksoftirqd/0] 5 root 16:03 [kworker/0:0] 7 root 16:03 [migration/0] 8 root 16:03 [migration/1] 9 root 16:03 [kworker/1:0] 10 root 16:03 [ksoftirqd/1] 11 root 16:03 [cpuset] 12 root 16:03 [khelper] 13 root 16:03 [kworker/u:1] 38 root 16:03 [kworker/1:1] 215 root 16:03 [sync_supers] 217 root 16:03 [bdi-default] 219 root 16:03 [kblockd] 225 root 16:03 [ata_sff] 236 root 16:03 [khubd] 242 root 16:03 [md] 265 root 16:03 [rpciod] 278 root 16:03 [kswapd0] 279 root 16:03 [fsnotify_mark] 280 root 16:03 [nfsiod] 281 root 16:03 [crypto] 319 root 16:03 [scsi_eh_0] 322 root 16:03 [scsi_eh_1] 325 root 16:03 [kworker/u:2] 336 root 16:03 [comcerto_spi.1] 338 root 16:03 [comcerto_spi.0] 371 root 16:03 [btn_t] 381 root 16:03 [a3gblink_t] 416 root 16:03 [md1_raid1] 418 root 16:03 [kjournald] 1962 root 16:04 [kworker/0:2] 2200 root 16:04 [pfe_ctrl_timer] 4192 root 16:04 [jbd2/sda4-8] 4197 root 16:04 [ext4-dio-unwrit] 4207 root 16:04 [ext4lazyinit] 4212 root 16:04 [flush-8:0] 5997 root 16:04 [lockd] 5998 root 16:04 [nfsd] 5999 root 16:04 [nfsd] 6000 root 16:04 [nfsd] 6001 root 16:04 [nfsd] 6002 root 16:04 [nfsd] 6003 root 16:04 [nfsd] 6004 root 16:04 [nfsd] 6005 root 16:04 [nfsd] 29125 root 23:22 [flush-9:1] iTunes in my PC doesn't seem to recognize/load MyBookWorld. It keeps: "Loading 'MyBookWorld'" for hours, I even left overnight.
In Config > media > itunes, I have it configured like this:
- Service enabled: checked
- Music: Public/Shared Music (default - where i have tons of music)
- media server name: "MyBookWorld" (default)
- Check for new music every: 1 day (default)
For everything else my PC is accessing the WD MyBookWorld ok: file system, twonky, etc.
Any suggestions?
Thanks
Raphael
Greetings all. I recently installed Accessbook on my MBWE-WL. I can play AVI right from Accessbook via the green play arrow next to the video file, but no other format I use (mkv, mp4) has a play arrow. Anyone know what gives with that, or better yet, how to fix it?
Thanks in advance!!
Hi,
I managed to short the circuits in the enclosure of my MBW 1TB drive, and need to get at the files contained on it. I've put it in a caddy and it seems healthy enough, only I don't have enough knowledge to do anything except look at the unmounted drives in Disk Utility. Ideally I'd like a way of accessing the drives via Terminal so that I can mount them in Finder and get at my files. Would the "unbricking" tutorial help me? or would I need to go reinstall in a new MBW enclosure to make this work.
Any suggestions?
Many thanks
S.
Hi.
I have a MBWE white light with some issues. I can turn on the system, access the data and start copying to another system, but after some seconds, the connection is lost.
Can I remove the HDD and connect to a PC just for data recovery? I know the HDD is in good condition. I don't know why 3 of my MBWE have the same problem now (hangs or freeze) after few seconds. I have exactly the same issue with 3 systems. Already upgrade firmware and restore to factory defaults but the problem is still there.
But for now I just want to recover some data from one of them. HDD is good.
Thanks.